(02) 90112078 | 
Contact us |  
COMPUTER HARDWAREPC & NOTEBOOKSSOFTWAREPRINTERS & SCANNERSSERVERSNETWORKINGELECTRONICS

Kingston KVR16LE11S8/4I 4GB 1600MHz DDR3L ECC CL11 DIMM SR x8 1.35V w/TS Intel - Server Memory

Model: KVR16LE11S8/4I / Item No: 324291

Kingston KVR16LE11S8/4I 4GB 1600MHz DDR3L ECC CL11 DIMM SR x8 1.35V w/TS Intel - Server Memory

More Views

Details

KVR16LE11S8/4I
4GB 1Rx8 512M x 72-Bit PC3L-12800
CL11 240-Pin ECC DIMM

DESCRIPTION
This document describes ValueRAM's 512M x 72-bit (4GB)
DDR3L-1600 CL11 SDRAM (Synchronous DRAM), 1Rx8, ECC,
low voltage, memory module, based on nine 512M x 8-bit FBGA
components. The SPD is programmed to JEDEC standard
latency DDR3-1600 timing of 11-11-11 at 1.35V or 1.5V. This
240-pin DIMM uses gold contact fingers. The electrical and
mechanical specifications are as follows:
FEATURES
• JEDEC standard 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~
1.575V) Power Supply
• VDDQ = 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V)
• 800MHz fCK for 1600Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Thermal Sensor Grade B
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB: Height 1.18” (30mm), single sided component

Details

SPECIFICATIONS
CL(IDD) 11 cycles
Row Cycle Time (tRCmin) 48.125ns (min.)
Refresh to Active/Refresh 260ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 35ns (min.)
Maximum Operating Power (1.35V) = 1.822 W*
(1.50V) = 2.025 W*
UL Rating 94 V - 0
Operating Temperature 0o
 C to 85o
 C
Storage Temperature -55o C to +100o
 C
*Power will vary depending on the SDRAM.

Details

Shipping Calculator

 
 
Skycomp Technology uses the best carriers in the business to make sure your order gets to you on time.
 
Australia Post eParcel 
eParcel generally takes 2-10 business days to be delivered depending on final destination.
We recommend you use this service for PO Box or if you believe your delivery address will be unattended as you will be able to collect this from your local Post Office. 

Australia eParcel Express
eParcel Express generally takes 1-3 business days to be delivered depending on final destination.
We recommend you use this service for PO Box or if you believe your delivery address will be unattended as you will be able to collect this from your local Post Office.

Other prefered partner
• Local Express:Delivered in 1-2 Business Days 
• Nationwide Delivery: 1-4 Business Days* 
• Nationwide Express: Next Business Day* 
*Allow extra days for regional areas 
 
 
All orders will be shipped from our Australian (NSW/QLD/VIC/WA) warehouses. More than 95% order are shipped via Australia Post E-Parcel and some from our preferred Partner listed below:
 

Following are the contact details of the freight companies we use:

 

IN STORE PICK UP IN SYDNEY
Ph: 02-92800583 
Usually 24 hours after placing your order.

Your requirements will be our passion

For IMMEDIATE customer service assistance or help with an order please


  • Reload captcha

* Required Fields

Have you considered this?