SKYCOMP Online Store is now open & shipping nationwide.

X
Australia's Leading Online Computer Store
Your Cart

Buy Cisco Lte-antm-sma-d= Lte Sma Dipole Antenna 698-960

Cisco Lte-antm-sma-d= Lte Sma Dipole Antenna 698-960

Delivery

In Stock
Usually ships within 24 hours*
no surcharge fee
Paypal/MasterCard/Visa/Amex
was $55
$45
Save $10
Overview This document provides the description, supported features, and installation instructions for the Cisco 3G/4G LTE and LTEA Omnidirectional Dipole Antenna (LTE-ANTM-SMA-D). The LTE-ANTM-SMA-D omnidirectional dipole antenna is designed for indoor use with Cisco 4G Long Term Evolution (LTE) and Long Term Evolution Advanced (LTEA) Service Routers (ISRs) and Pluggable Modules with an SMA connector. The LTE-ANTM-SMA-D antenna is marked with a dual green band to indicate that it supports Cisco LTEA routers and modules. This antenna has the following features: Support for frequencies of 698-960, 1448-1511, and 1710-2690 MHz. Standalone antenna peak gain of less than 3.7 dBi in the supported frequency bands. Articulating joint that can maneuver into three stop positions: 0°, 45°, and 90°. Male SubMiniature A connector that allows direct mounting of the antenna to any Cisco supported router or Pluggable Module with an SMA connector. The SMA connector design has added rotational frictional torque to ensure the SMA interface stays properly mated, and to reduce chances of a disconnect. The design is also more finger friendly compared to a classic SMA hex nut design. For optimal performance, we strongly recommend that you use two antennas to take full advantage of MIMO technology on all Cisco cellular routers that support MIMO (4G LTE and later releases). Figure 1. Cisco LTE-ANTM-SMA-D Omnidirectional Dipole Antenna, SMA Connector and Articulating Joint: See the following table:   1 SMA connector 0° position 2 SMA connector 45° position 3 SMA connector 90° position 4 Articulating Joint 5 Product ID Specifications Table 1. Specifications of the LTE-ANTM-SMA-D antenna: Operating Frequencies 698-960 MHz 1447-1511 MHz 1710-2690 MHz Polarization Vertical, linear Nominal Impedance 50 Ohms Peak Gain 2.0 dBi (698-960 MHz) 2.8 dBi (1447-1511 MHz) 3.7 dBi (1710-2690 MHz) Note  The standalone antenna peak gain numbers are provided above. When you install an antenna close to metallic objects or directly on chassis, the peak gain will be affected. We recommend that you keep antennas away from very large chassis and metallic objects. You can install antennas directly on smaller or medium size chassis. In all cases, we recommend that you keep different antennas away from each other and from various known sources of electromagnetic radiation. VSWR ≤ 2.5:1 (698-960 MHz) ≤ 2.5:1 (1447-1511 MHz) ≤ 2.0:1 (1710-2690 MHz) Maximum RF Input Power 5 W DC Power No DC power required for LTE-ANTM-SMA-D antenna operation. Dimensions 9” (L) x 1.46” (W) x 0.43” (D) (229 x 37 x 11 mm) Weight 56.8 grams Efficiency LTE-ANTM-SMA-D antennas have high standalone efficiency, and maintain high efficiency when directly installed on front plate of a small or medium size Cisco router. However, depending on chassis size and a variety of other electromagnetic considerations, installing the antenna directly on the chassis is not always recommended. Temperature Range -30°C to + 70°C (Operating) -40°C to + 85°C (Storage)
45 45 AUD 100
SKU
LTE-ANTM-SMA-D=
SKU#: LTE-ANTM-SMA-D= / ITEM NO: 769588 / BRAND: Cisco
Rating:
Special Price $45.00 Regular Price $55.00
Shipping Calculator:
Loading...
LTE SMA dipole antenna 698-960 1448-1511 1710-2690

Picture shown is for illustration purpose only
Please refer to Manufacturer SKU for the exact details

Overview

This document provides the description, supported features, and installation instructions for the Cisco 3G/4G LTE and LTEA Omnidirectional Dipole Antenna (LTE-ANTM-SMA-D).

The LTE-ANTM-SMA-D omnidirectional dipole antenna is designed for indoor use with Cisco 4G Long Term Evolution (LTE) and Long Term Evolution Advanced (LTEA) Service Routers (ISRs) and Pluggable Modules with an SMA connector.

The LTE-ANTM-SMA-D antenna is marked with a dual green band to indicate that it supports Cisco LTEA routers and modules.

This antenna has the following features:

  • Support for frequencies of 698-960, 1448-1511, and 1710-2690 MHz.
  • Standalone antenna peak gain of less than 3.7 dBi in the supported frequency bands.
  • Articulating joint that can maneuver into three stop positions: 0°, 45°, and 90°.
  • Male SubMiniature A connector that allows direct mounting of the antenna to any Cisco supported router or Pluggable Module with an SMA connector.
  • The SMA connector design has added rotational frictional torque to ensure the SMA interface stays properly mated, and to reduce chances of a disconnect. The design is also more finger friendly compared to a classic SMA hex nut design.

For optimal performance, we strongly recommend that you use two antennas to take full advantage of MIMO technology on all Cisco cellular routers that support MIMO (4G LTE and later releases).

Figure 1. Cisco LTE-ANTM-SMA-D Omnidirectional Dipole Antenna, SMA Connector and Articulating Joint:

See the following table:

 

1

SMA connector 0° position

2

SMA connector 45° position

3

SMA connector 90° position

4

Articulating Joint

5

Product ID

Specifications

Table 1. Specifications of the LTE-ANTM-SMA-D antenna:

Operating Frequencies

698-960 MHz

1447-1511 MHz

1710-2690 MHz

Polarization

Vertical, linear

Nominal Impedance

50 Ohms

Peak Gain

2.0 dBi (698-960 MHz)

2.8 dBi (1447-1511 MHz)

3.7 dBi (1710-2690 MHz)

Note 
The standalone antenna peak gain numbers are provided above. When you install an antenna close to metallic objects or directly on chassis, the peak gain will be affected. We recommend that you keep antennas away from very large chassis and metallic objects. You can install antennas directly on smaller or medium size chassis. In all cases, we recommend that you keep different antennas away from each other and from various known sources of electromagnetic radiation.

VSWR

≤ 2.5:1 (698-960 MHz)

≤ 2.5:1 (1447-1511 MHz)

≤ 2.0:1 (1710-2690 MHz)

Maximum RF Input Power

5 W

DC Power

No DC power required for LTE-ANTM-SMA-D antenna operation.

Dimensions

9” (L) x 1.46” (W) x 0.43” (D) (229 x 37 x 11 mm)

Weight

56.8 grams

Efficiency

LTE-ANTM-SMA-D antennas have high standalone efficiency, and maintain high efficiency when directly installed on front plate of a small or medium size Cisco router. However, depending on chassis size and a variety of other electromagnetic considerations, installing the antenna directly on the chassis is not always recommended.

Temperature Range

-30°C to + 70°C (Operating)

-40°C to + 85°C (Storage)

LTE SMA dipole antenna 698-960 1448-1511 1710-2690

Our customer service staff are standing by to assist you. Should you have questions about this product, please complete the form below and we'll be in touch soonest possible. We aim to answer your enquiries within 24 hours.

For IMMEDIATE customer service assistance or help with an order please call our Customer Service Team on: 02 9011 2078